Devika Prep PortalNEET & JEE Main practice

Free practice › JEE Main

JEE Main · Physics · NCERT Class 12 Physics, Chapter 3

Current Electricity Formulas for JEE Main

All 22 formulas of Current Electricity on one page, each with a short note on what the letters mean or when to use it. Print it and keep it for quick revision.

Current and Ohm's law

I = Q / t
I = current (A), Q = charge crossing the area in time t. 1 A = 1 C s−1
V = IR
Ohm's law: V = potential difference across the conductor, R = its resistance (Ω). Holds only while R does not change with I
R = ρl / A
ρ = resistivity of the material (Ω m), l = length, A = area of cross-section. Doubling l doubles R; doubling A halves R
σ = 1 / ρ
σ = conductivity (S m−1). j = σE links current density to the electric field inside the conductor

Drift of electrons

vd = eEτ / m
vd = drift speed, E = field inside the conductor, τ = relaxation time (average time between collisions), m = electron mass
I = neAvd
n = number of free electrons per unit volume, A = area of cross-section. Current density j = I/A = nevd
ρ = m / (ne2τ)
Resistivity from the drift model: more electrons (n) or longer τ → lower ρ
μ = vd / E = eτ / m
μ = mobility of the charge carriers (m2 V−1 s−1)

Resistance and temperature

ρT = ρ0 [1 + α(T − T0)]
α = temperature coefficient of resistivity (per °C or per K); ρ0 at the reference temperature T0. Same form for R: RT = R0 [1 + α(T − T0)]
α = (RT − R0) / (R0 (T − T0))
How to find α from two resistance readings. α > 0 for metals (R rises with T), α < 0 for semiconductors

Electrical power

P = VI = I2R = V2 / R
P = power dissipated as heat in a resistor (W). Use I2R when the current is known, V2/R when the voltage across it is known
H = I2Rt
Heat produced (J) in time t. Power lost in transmission lines ∝ I2 — that is why power is sent at high voltage and low current

Cells: emf and internal resistance

V = ε − Ir
V = terminal voltage while a current I flows, ε = emf, r = internal resistance. V = ε when no current is drawn (open circuit)
I = ε / (R + r)
Current through an external resistance R connected to the cell
εeq = ε1 + ε2 , req = r1 + r2
Two cells in series (positive of one to negative of the other). If one cell is reversed, its emf is subtracted
εeq / req = ε1 / r1 + ε2 / r2 , 1 / req = 1 / r1 + 1 / r2
Two cells in parallel: the two equations together give εeq and req

Combination of resistors

Rs = R1 + R2 + R3 + …
Series: same current through each; total resistance is the sum (larger than any one)
1 / Rp = 1 / R1 + 1 / R2 + 1 / R3 + …
Parallel: same voltage across each; total resistance is smaller than the smallest. For two: Rp = R1R2 / (R1 + R2)

Kirchhoff's rules and Wheatstone bridge

Σ Iin = Σ Iout
Junction rule: at any junction, total current entering = total current leaving (charge is conserved)
Σ ΔV = 0 around any closed loop
Loop rule: going round a closed loop, the algebraic sum of potential changes is zero. Take −IR along the current, +ε from − to + of a cell
R1 / R2 = R3 / R4
Balanced Wheatstone bridge: no current through the galvanometer (null point). Then the unknown R4 = R3 · R2 / R1
R / S = l / (100 − l)
Metre bridge (a Wheatstone bridge with a 1 m wire): R and S = the two resistances in the gaps, l = balancing length in cm measured from the end on R's side

Source: NCERT Physics Class 12 Part 1, Chapter 3. Written by Devika Prep Portal in its own words from the NCERT textbook; every formula is checked twice.

More formula sheets in the app

Chapter-wise formula sheets for JEE Main (61 chapters), with practice questions, past papers and mock tests.

Start free — 8 days